Sht31 Temperature Sht31-d Humidity Sensor Module Microcontroller Iic I2c Breakout Weather 3v 5v Compliant For Arduino

6 790,00 Ft
+ 3 049,00 Ft szállítási költség

Sht31 Temperature Sht31-d Humidity Sensor Module Microcontroller Iic I2c Breakout Weather 3v 5v Compliant For Arduino

  • Márka: Unbranded
Értékesítő:

Sht31 Temperature Sht31-d Humidity Sensor Module Microcontroller Iic I2c Breakout Weather 3v 5v Compliant For Arduino

  • Márka: Unbranded
Ár: 6 790,00 Ft
Értékesítő:
6 790,00 Ft
+ 3 049,00 Ft szállítási költség

Készleten

A következő fizetési módokat fogadjuk el

Leírás

SHT31 Description:  Sensiron Temperature/Humidity sensors are some of the finest & highest-accuracy devices you can get. And, finally we have some that have a true I2C interface for easy reading. The SHT31-D sensor has an excellent ±2% relative humidity and ±0.3°C accuracy for most uses. Unlike earlier SHT sensors, this sensor has a true I2C interface, and (bonus ) even with two address options. It also is 3V or 5V compliant, so you can power and communicate with it using just about any microcontroller or microcomputer. Such a lovely chip - so we spun up a breakout board with the SHT31-D and some supporting circuitry such as pullup resistors and capacitors. Each order comes with one fully assembled and tested PCB breakout and a small piece of header. You'll need to solder the header onto the PCB but it's fairly easy and takes only a few minutes even for a beginner. Power Pins: Vin - this is the power pin. The chip can use 2.5-5VDC for power. To power the board, give it the same power as the logic level of your microcontroller - e.g. for a 5V micro like for Arduino, use 5V. For a 3.3V controller like a Raspbery Pi, connect to 3.3V GND - common ground for power and logic I2C Logic pins: SCL - I2C clock pin, connect to your microcontrollers I2C clock line. This pin has a 10K pullup resistor to Vin SDA - I2C data pin, connect to your microcontrollers I2C data line. This pin has a 10K pullup resistor to Vin Other Pins: ADR - This is the I2C address selection pin. This pin has a 10K pull down resistor to make the default I2C address 0x44. You can tie this pin to Vin to make the address 0x45 RST - Hardware reset pint. Has a 10K pullup on it to make the chip active by default. Connect to ground to do a hardware reset ALR - Alert/Interrupt output. You can set up the sensor to alert you when an event has occured. Check the datasheet for how you can set up the alerts
  • Fruugo azonosító: 61760356-124444078
  • EAN: 3461031394556

Kiszállítás és visszaküldés

Kiküldés 4 napon belül

  • STANDARD: 3 049,00 Ft - közötti szállítás K 28 október 2025–Sze 05 november 2025

Szállítás innen: Kína.

Minden tőlünk telhetőt megteszünk annak biztosítására, hogy rendelését hiánytalanul és előírásainknak megfelelően szállítás ki önnek. Viszont ha egy hiányos rendelést kap, vagy eltér a megrendelttől, vagy bármilyen más okból nem elégedett a rendeléssel, akkor visszaküldheti a rendelést vagy a rendelésben lévő bármely terméket, és visszatérítik a termék árának teljes összegét. Teljes visszaküldési irányelvek megtekintése.

Termékmegfelelőségi részletek

Kérjük, tekintse meg a termékre vonatkozó megfelelőségi információkat az alábbiakban.

Az alábbi információkat a terméket értékesítő független, harmadik fél kiskereskedő biztosítja.

Gyártó:
Az alábbiakban olvashatók a Fruugo platformján értékesített releváns termék gyártójának elérhetőségei.

  • dongguanshiminganguangoumaoyiyouxiangongsi
  • dongguanshiminganguangoumaoyiyouxiangongsi
  • Room 503, No. 33, Lane 2, Changhong NewTown, 1st Road, Dalang Town
  • Dongguan
  • CN
  • 523004
  • minganguangou@163.com

Felelős személy az EU-ban:
Az alábbiakban olvashatók az Európai Unióban kijelölt felelős személy elérhetőségei. A felelős személy az az Európai Unióban székhellyel rendelkező gazdasági társaság, amely az Európai Unióban eladott releváns termékekhez kapcsolódó megfelelőségi kötelezettségekért felel.

  • E-CrossStu GmbH
  • E-CrossStu GmbH
  • 69 Mainzer Landstrasse
  • Frankfurt am Main
  • Germany
  • 60329
  • E-CrossStu@web.de
  • 49 69332967674